Tool Kit

The following is the recommended tool kit.

  • Torx driver set: T9, T10
  • Phillips #1 screwdriver
  • Flathead screwdriver
  • Metric hex key set: 1.5, 2, 2.5, 3, 4 mm
  • Metric hex key with ball-end: 3 mm
  • SAE hex key: 3/32 inch
  • Lens brush
  • Socket wrench (1/4" drive)
  • Socket set: 14 mm spark plug socket
  • Crescent wrench
  • Needle nose pliers
  • Flush cutter
  • Torque wrench: 0-15 in/lbs, 0-65 in/lbs, 10-150 in/lbs
  • SMA torque wrench
  • 8 mm wrench
  • Threadlocker: Loctite 242, 272
  • Adhesives: E6000, medium CA glue
  • Zipties
  • X-Acto knife
  • Cables: USB-A to USB-C, USB-A to USB micro, FTDI to JST-GH, ethernet
  • Flashlight
  • Safety wire pliers
  • Safety wire
  • Torque stripe

Spare Hardware

FPS

Item Fastener QTY Torque Threadlocker
Spark Plugs NGK CM-6 2 90 in/lbs (10 Nm) n/a
Prop Bolts M5 x 70 SHCS 6 65 in/lbs (7.3 Nm) n/a
Spinner Cone Bolt M5 x 100 SHCS 1 30 in/lbs (3.4 Nm) Blue Loctite 242
Muffler Bolts M5 x 20 SHCS 2 per 60 in/lbs (6.8 Nm) n/a
Muffler Support Bracket M4 x 8 SHCS 1 per n/a
Throttle Body Bolts HFE0807 2 30 in-lb (3.4 Nm) Blue Loctite 242
Cylinder Bolts M5 x 13 4 per 70 in/lbs (8 Nm) Blue Loctite 243
Crank Case Bolts M5 x 20 4 70 in/lbs (8 Nm) Blue Loctite 243
Air Filter Locknuts MFE0384 2 10 in/lbs (1.1 Nm) n/a
Engine Latch Bolts M5 x 20 flat head 2 30 in/lbs (3.4 Nm) Blue Loctite 242

VPS

Item Fastener QTY Torque Threadlocker
Motor Pod Screw M4 x 8 SHCS 6 25 in/lbs (2.8 Nm) Loctite 242
Motor Pod Washer M4 washer 6 n/a n/a
Top Motor Hatch M3 x 8 button 4 hand-tight n/a
Bottom Motor Hatch M3 x 8 button 4 hand-tight n/a
Propeller M3 x 30 SHCS 4 15 in/lbs (1.7 Nm) Loctite 242
D-Sub Connector 4-40 x 3/16 SHCS 2 hand-tight Loctite 242

Landing Gear

Item Fastener QTY Torque Threadlocker
Central Foot M4 x 10 SHCS 2 hand-tight n/a
Rear Foot M4 x 14 SHCS 2 hand-tight n/a
Item Fastener QTY Torque Threadlocker
Nav Light Cover M3 x 14 button 2 hand-tight n/a

Servos

Item Fastener QTY Torque Threadlocker
Servo Tray M3 x 8 flat head 4 hand-tight n/a
Servo Mount M2.5 x 12 thread former 4 hand-tight n/a
Clevis Lock Safety Lock Kwik-Link 1 n/a n/a

Airframe

Item Fastener QTY Torque Threadlocker
Hatches M3 x 8 button - hand-tight n/a
Payload Fairing M4 x 8 button head 9 hand-tight n/a
Draw Latches M3 x 8 flat head thread former 2 hand-tight n/a
D-Sub Connector M3 x 8 button 2 hand-tight n/a
D-Sub Connector, Tail M3 x 8 thread former 2 hand-tight n/a

Transponder

Item Fastener QTY Torque Threadlocker
Transponder Hatch M3 x 8 button 6 hand-tight n/a
Front Mounting Screws M3 x 30 button 2 12 in/lbs Blue Loctite 242
Rear Mounting Screws M3 x 25 button 2 12 in/lbs Blue Loctite 242
Blade Antenna M3 x 12 flathead 2 12 in/lbs Blue Loctite 242

Pitot System

Item Fastener QTY Torque Threadlocker
Airspeed Tubing, Probe Festo 2 x 1 mm n/a n/a n/a
Airspeed Tubing, Avionics Festo 3 x 1 mm n/a n/a n/a
Pitot Tube Mount M3 x 8 thread former 2 hand-tight n/a

results matching ""

    No results matching ""